Hearth & Harvest

How to Fix a Leaky Faucet

By the Hearth & Harvest Editorial Team · Updated November 16, 2026

Person closing the shut-off valve under a bathroom sink

Most dripping faucets are caused by one worn part inside the handle: a rubber washer, an O-ring, a cartridge, or the seals in a ball or ceramic disc valve. To fix it, turn off the water under the sink, figure out which type of faucet you have, take the handle apart, and replace the worn part with an exact match. It's a manageable job for a beginner with basic tools and patience.

Water repairs are a core skill in our DIY & Repairs section, and the first one is always finding your shut-off valves.

Before you start: find your shut-offs

Fixture shut-offs. Look under the sink. You'll usually see two small valves on the pipes coming out of the wall, one for hot and one for cold. Turn each one clockwise until it stops. Don't force it; old valves can crack.

The main shut-off. Every home has a main valve that stops water to the whole house. It's often near the water meter, in a basement, crawl space, garage or utility closet, or where the water line enters the house. Find it now, before you need it in a hurry. Renters can ask their landlord or building manager.

Test it. After closing the fixture valves, open the faucet. A little water will drain out, then it should stop. If water keeps flowing, the valves aren't sealing. Use the main shut-off, and plan to have a plumber replace the fixture valves.

Identify your faucet type

Faucets fall into four general types. You can often tell by how the handle moves.

Faucet typeHow it worksPart that usually wears
CompressionTwo handles you twist down to tightenRubber washer and seat
CartridgeOne or two handles; smooth movementThe cartridge or its O-rings
BallSingle handle on a rounded cap, moves in all directionsSprings and rubber seats
Ceramic discSingle lever over a wide cylinderRubber seals around the discs

If you're not sure, take a photo of the faucet and bring it, along with the old part once you remove it, to a hardware store. Exact matches matter.

What you'll need

  • An adjustable wrench and slip-joint pliers
  • A multi-bit screwdriver and possibly a hex (Allen) key
  • A rag, a small towel and a container for parts
  • Replacement parts matched to your faucet
  • Plumber's grease if the replacement instructions call for it
  • Safety glasses

Step-by-step repair

  1. Shut off the water and open the faucet to drain the lines.
  2. Plug the drain with a stopper or rag so small screws can't fall in.
  3. Lay out a towel and set parts on it in the order you remove them. Take photos as you go.
  4. Remove the handle. Pry off the decorative cap if there is one, then unscrew the handle screw beneath it. Some handles use a small hex screw on the side.
  5. Remove the inner parts. Depending on the type, you'll unscrew a packing nut, pull out a cartridge with its retaining clip, or lift out the ball and its seals. Wrap the wrench jaws in a rag to avoid scratching the finish.
  6. Inspect and replace. Look for flattened, cracked or hardened rubber, mineral buildup or a worn cartridge. Replace the worn parts with exact matches, following the package instructions.
  7. Reassemble in reverse order, using your photos as a guide. Snug fittings without overtightening.
  8. Turn the water back on slowly and check for drips at the spout and around the handle.

If the faucet still drips, the seat inside a compression faucet may be worn, or a different seal may be at fault. That's often the point where a plumber can save you time.

When to call a licensed plumber

Small faucet repairs are fine to do yourself. Call a licensed plumber if:

  • The shut-off valves won't close, or they leak when you touch them.
  • Water is leaking from the supply lines, the pipes in the wall or under the floor.
  • You see corrosion, soft cabinet floors or water stains below the sink.
  • You need to replace the valve itself, cut pipe or solder anything.
  • The job involves a water heater, gas line or main water line.

Your local permit rules may also apply to bigger plumbing changes, so ask before you replace fixtures or move pipes.

Finishing touches around the sink

Once the drip is gone, look at the seal where the faucet and sink meet the counter. Cracked or moldy caulk lets water seep under the fixture. Our guide to caulking and weatherstripping shows how to remove old caulk and run a clean new bead. If the sink also drains slowly, now's a good time to tackle that with our steps for clearing a drain. And if past drips left water stains on nearby walls, our guide to painting a room covers the stain-blocking primer and prep that keeps them from showing through.

Saving the water you do use

A dripping faucet wastes water you're paying for, and fixing it is one simple way to cut waste. If you garden and want to make better use of water outdoors, our guide to rainwater harvesting covers rain barrels and the rules that vary by state.

A worked example: a dripping bathroom sink

Example: Avery, 31, notices their single-handle bathroom faucet drips at night. They close both valves under the sink, plug the drain and pull off the handle. Inside is a cartridge with a worn O-ring. They take the cartridge to a hardware store, buy a match, and swap it in following the package directions. The drip stops. If it hadn't, Avery's plan was to call a plumber rather than keep taking the faucet apart.

Something to do this weekend

Find the shut-off valves under every sink and toilet in your home, and find your main water shut-off. Gently test each fixture valve. Write down which ones stick or leak, and plan to have a plumber replace those before an emergency makes the job urgent.

Partner offer · paid placement

Want a step-by-step plan or guide?

Some people like the structure of a paid guide or set of plans. This button opens a third-party program from one of our advertising partners. Its claims are its own, not ours, so weigh them against our checklist for judging paid plans.

See the partner program →

We may be paid when you click. The program shown can change. Read its terms before you buy anything. How this works

Frequently asked questions

Why does my faucet keep dripping after I turn it off?

Usually a worn part inside the faucet, such as a rubber washer, an O-ring, a cartridge or the seals in a ball or ceramic disc valve, isn't sealing fully. Replacing that part often stops the drip.

Where is the shut-off valve for my sink?

Most sinks have two small valves underneath, one for hot and one for cold. Turn them clockwise to close. If there are none, or they won't close, use your home's main shut-off valve.

When should I call a plumber for a leaky faucet?

Call a licensed plumber if the shut-off valves won't close or are leaking, if the leak is coming from the supply lines or pipes, if you see corrosion or water damage, or if you can't stop the drip after replacing parts.

See a partner guidePartner offer
Partner offer · paid placement

Want a step-by-step guide?

If you'd like more structure than articles can give, you can look at a third-party guide or set of plans from one of our partners. Its claims are its own. No pressure: our free guides aren't going anywhere.

See the partner program →

We may be paid when you click. How this works